Eicon Networks D/120JCT-LSU User Manual download pdf

Part number: 64-0063-02

Dialogic

D/120JCT-LSU

Installation Guide

1. Product Description

The Dialogic

D/120JCT-LSU combined media

board (“board”) is a 12-port analog telecom board in

a PCI form factor with universal connectivity

(support for both 5 V and 3.3 V signaling). The D/

120JCT-LSU is well suited for advanced

communications applications that require

multimedia resources. This high-performance,

scalable product supports voice, fax, and software-

based speech recognition processing in a single

PCI slot, and provides 12 analog telephone interface

circuits for direct connection to analog loop start

lines.

The physical features of the D/120JCT-LSU board

include the following:

SW100: Rotary switch used to determine board ID

SW1: Slide switch for on/off hook on power up

J1-J6: RJ-14 connectors, two analog telephone

lines per connector

Additional Information

Additional information about the D/120JCT-LSU is

available from a number of sources.

The product data sheet, available at http://

www.dialogic.com/products/list.asp, provides a

functional description as well as information about

applications and configurations, features, and

technical specifications.

Refer to the Release Guide and the online Release

Update for your Dialogic

system software release

to verify that the D/120JCT-LSU is supported in the

release and for information on any new features or

issues that may relate to it.

The Regulatory Notices document that is packed

with each D/120JCT-LSU board contains safety

warnings and national requirements for proper

operation of telecommunications equipment.

2. Before You Begin

Protecting the Board from Damage

CAUTION: All computer boards are sensitive to

electrostatic discharge (“ESD”). Handle all static-

sensitive boards and components at a static-safe

work area, and observe anti-static precautions at all

times.

If you are not familiar with ESD safety precautions,

visit http://dialogic.com/support/hwinstall to learn

more.

Unpacking the Board

CAUTION: Do not remove the board from the anti-

static packaging until you are ready to install it.

Observe proper anti-static precautions at all times.

Unpack the board according to the following steps:

1. Prepare a static-safeguarded work area.

2. Carefully remove the board from the shipping

carton and static-shielding bag. Handle the

board by the edges and avoid touching the

board's components.

3. Lay the board on the static-safe work surface.

Note: Place boards in static-shielding bags when

carrying boards from station to station.

3. Configuring the Board

The D/120JCT-LSU board uses Plug and Play

technology, including hardware auto-configuration

for IRQ and memory address. This allows you to use

the factory default hardware settings for quick

installation and operation of the board.

In addition to the automatically configured items, the

D/120JCT-LSU board has two manually configurable

options, which are described in the following

sections:

■

Board ID

■

Hook-switch state at start-up

Setting the Board ID

When you start Dialogic

boards, each board is

assigned an identification for use by the application

program. The board number is based on the board

ID that is set through hardware switches on the

board (rotary switch SW100).

Set the board ID switches to select the board

sequencing method as follows.

Geographical Sequence (by PCI Bus and Slot

Number) Board ID 0 (factory default): All

Dialogic

PCI boards can share the factory

default setting of board ID 0; in this case, board

numbers are assigned in ascending order based

on the PCI bus and slot number. If you add a

board to the system, it could change the board

numbering, depending upon the PCI bus and slot

number where you install it. Also, PCI boards that

use ID 0 for the geographical numbering

sequence will be numbered before boards that

use board IDs 1-9, A-F. The geographical method

is not available for ISA bus telecom boards.

Programmable Sequence (by Board ID): Board

IDs 1-9, A-F: In addition to the geographical

assignment method, the programmable

assignment method can be used to further identify

the boards in your system. If you change the

board ID from the factory default of 0 to any other

number, the software will use that setting to

identify the board. This method is also used for all

ISA bus boards.

CAUTION: When not set to 0 to use the

geographical sequence method, each PCI board

must be set to a unique ID number. The ID setting

must not conflict with the board ID of any other Intel

ISA or PCI telecom board which has been manually

assigned.

Precedence in Mixed Systems: In systems using

both board numbering methods, or where both

ISA and PCI boards exist in the same system, PCI

boards take precedence and will be numbered

before an ISA bus board that uses a specific

board ID (1-9, A-F).

Setting the Hook-Switch State for

Start-Up (Optional)

Slide switch SW1 determines how the D/120JCT-

LSU board responds to an incoming call when the

PC power is on, but the board is not yet initialized.

With SW1 set to the ON position, the D/120JCT-LSU

board responds as off-hook while unititialized; with

SW1 set to the OFF position, the board responds as

on-hook.

4. Installing the Board

CAUTION: These procedures assume familiarity

with the general terminology associated with

electronic equipment and with the safety practices

and regulatory compliance required for using and

modifying electronic equipment.

These procedures should be performed only by

qualified technical personnel.

WARNING! Unplug the equipment before

performing the procedures described here.

Failure to disconnect the power before you open

the chassis can result in personal injury. Ensure

that the system is disconnected from its power

source and from all telecommunications links,

networks, or modem lines whenever the chassis

cover is removed. Do not operate the system

with the cover removed.

CAUTION: To avoid possible damage to the board,

remove power from the computer before beginning

installation. Observe proper anti-static precautions

at all times while handling and installing the board.

Install each board in the PC chassis using adjacent

PCI slots according to the following instructions.

1. Turn off all power to the system, and disconnect

the system's power cords from electrical outlets.

2. Remove the PC cover.

3. Select an empty PCI expansion bus slot, and

remove the slot's retaining screw and access

coverplate.

Physical Layout

1 2

Summary of Contents

Page 1 - D/120JCT-LSU

Page 2 - Installing the CT Bus Cable

4. Insert the board's edge connector into the bus slot. Apply pressure only to the top edge of the board, and gently rock the board forward and b

Comments to this Manuals

No comments

Eicon Networks D/120JCT-LSU User Manual

Browse online or download User Manual for Unknown Eicon Networks D/120JCT-LSU. Eicon Networks D/120JCT-LSU User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Eicon Networks D/120JCT-LSU